Weiconlock AN 302-22 Thread Locking Adhesive 20ml Pen

Vibration Proof, Non-Marking Removable Threadlocker

All Prices Include GST.

$19.93
In Stock
Available for Fast Dispatch.
Watch video
Buy In Bulk & Save!
Buy 1 to 9: Pay $19.93
Buy 10 to 19: Pay $16.35
Buy 20 to 39: Pay $15.90
Buy 40 or more: Pay $14.69

20ml Pens of this low strength, medium viscosity thread locker for connections that you want to be able to disassemble in the future. AN 302-22 withstands 150°C and is vibration-proof. Perfect for automotive and marine thread locking applications.

Browse our range of AN 302-22 Sizes.
Browse our range of Weiconlock AN 302-22 Sizes.
Threadlocking Adhesive Range Link
Browse our full Weiconlock Threadlockers Range.
  • Medium Viscosity.
  • Low Strength for Easy to Disassemble, Removable Bonds.
  • Non-Marking.
  • Vibration Proof.

Weiconlock AN 302-22 Threadlocking Adhesive is a low strength, medium viscosity grade designed to lock and seal threaded connections and prevent against unwanted loosening.

This grade of anaerobic adhesive is manufactured in Germany by Weicon and offers a variety of benefits. These are expanded on in the sections below:

Medium Viscosity.

Weiconlock AN 302-22  has a viscosity of 1000 nt mPa·s (according to Brookfield at 25°C). We classify this as a medium viscosity which means it will run a bit to fill smaller threads, but not so much that it is tricky to apply.

Weiconlock AN 302-22 is able to cover gaps up to 0.2mm and is used on threaded joints up to M 36.

Low Strength, Easy to Disassemble Joins.

Weiconlock AN 302-22 cures with low strength for bonding and sealing connections that should be easy to disassemble for frequent servicing or removal. Strength ratings are summarised further below.

Non-Marking.

Weiconlock AN 302-22 is a non-marking grade of threadlocker.

Vibration Proof.

Weiconlock AN 302-22 is vibration proof and maintains its adhesion for extended durations. This allows it to keep locked bolts in place until they are deliberately removed.

Weiconlock AN 302-22 Key Specs Overview.

Colour Purple
Threaded Joints Up To... M 36
Viscosity 1.000 mt mPa·s
Maximum Gap Bridging 0.2mm
Prevailing stregth 2 - 4 Nm
Handling Strength at Room Temperature 10 - 20 Minutes
Temperature Resistance -60°C to +150°C.

For more detailed information on this high-quality adhesive, please consult the specifications tab or the Technical Data Sheet via the Media Tab.

The Weiconlock Pen System.

One of the features of all Weiconlock Threadlockers, Flange Sealants, Retaining Adhesives and Pipe Sealers is the pen system they use for most size containers (300ml varieties are supplied in cartridges and are the one exception).

This special pen makes accurate application natural and easy. It also helps to reduce wastage as there’s less chance of spillage.

The Weicon Pen System has been used in all kinds of industries all over the world for decades and continues to be a key point of difference for these German-Made adhesives.

Common Features of All Weiconlock Anaerobic Adhesives.

WEICONLOCK® are one-component anaerobic adhesives and sealants, especially made for metal assembly parts.

The full range covers over 60 different grades designed for everything from Thread Locking, Pipe Sealing, Flange Sealing and Retaining Cylindrical Assemblies like bearings. There are special grades for potable water applications, gas lines, oxygen service and more.

No matter the grade chosen, all types of Weiconlock Adhesive have a few things in common:

Excellent Chemical Resistance.

All grades of Weiconlock Adhesives are resistant to a large variety of different chemicals, fluids and gases. Some of the more common are summarised in the table below. A more comprehensive list is also available via the Media Tab..

Media Resistance   Media Resistance
Acetic acid 80% o   Oxygen
(Only WEICONLOCK with BAM)
+
Aromat, Solvent +   Phenol +
Brake fluid +   Propane +
Diesel, heating oil +   Seawater +
Edible oil +   Silicone oil +
Fuel oil +   Turpentine +
Glycocol, glycine +   Vinegar +
Helium +   Water (acidic) under PH 7 +
Hydrochloric acid +   Water PH 7 to 8 +
Isobutane +   Water (alk.) over PH 8 +
Kerosene +   Water, chlorinated +
Mineral oil +   Water, cooked o
Naphtha, petroleum +   Water, distilled +
Natural gas - dry +   Water, wastewater (sewage) +
Nitrogen gas +   Xylene, dimethylbenzene +

+ = Good Resistance.
o = Resistant
% = Limited Resistance.
- = Not Resistant.

Easy to Use.

In general, WEICONLOCK does not require special pre-treatment as slightly oily surfaces (e.g. on as received parts) will be tolerated.

However, best results will be achieved on cleaned, degreased parts (use WEICON Surface Cleaner). If required, the parts should be slightly roughened.

WEICONLOCK is ready for use and should be applied evenly direct from the bottle/tube with the dispensing tip (avoid direct contact of dispensing tip with metal). Apply continuous bead on one side of flange, join and tighten parts quickly.

For sealing applications (pipe fitting) apply WEICONLOCK in circular motions on the thread. Screw pipe threads together and tighten until desired orientation.

Do not pour back into the bottle any WEICONLOCK fluid which had contact with metal; even smallest metal particles will cause the content of the bottle to cure. In series construction, the use of manual or automatic applicators is recommended.

Simple to Store.

WEICONLOCK can be stored in the unopened original container for at least 24 months at room temperature. Keep away from heat sources and direct sunlight. The air in the bottle/tube keeps WEICONLOCK liquid.

(SWM000152B01V0001)

What do I have to do to prepare the surfaces?

Clean and dry as much as possible. Weiconlock grades will work on slightly oily surfaces but adhesion will be improved on parts that have been cleaned and degreased.

How long does it take to dry?

About 3-6 hours at room temperature for complete curing. Handling strength (usually around 35% of the final strength) will be achieved much faster; about 10-20 minutes at room temperature.

The large range quoted here is a reflection of two things; the difference in what room temperature can mean and the fact that Weiconlock AN 302-22 will take slightly longer to cure on some surfaces than others. 

Colour Purple
For Threaded Joints Up To... M 36
Viscosity 1.000 mPa·s
Maximum Gap Bridging 0.2mm
Breakaway strength (Thread)  4 - 6 Nm
Prevailing stregth 2 - 4 Nm
Shear strength Nmm² (DIN 54452)* 3 - 5 N/mm²
Handling Strength at Room Temperature 10 - 20 Minutes
Final strength (100%) after 3 - 6 Hours
Temperature Resistance -60°C to +150°C.

*Strength values based on M 10 screws, 8.8 grade, thickness of nut 0,8.d Static shear strength based on cylindrical parts of abt. Ø 13 mm, tolerance (D-d) = 0,05 mm, l/d = 0,88 

SKU SWM000152B01V0001
Model # 30222020
Brand Weicon
Shipping Weight 0.0350kg
Shipping Width 0.025m
Shipping Height 0.190m
Shipping Length 0.025m
Shipping Cubic 0.000118750m3
Unit Of Measure ea

Technical & Safety Data Sheet.

TDS Link SDS Link      
Weiconlock AN 302-22 TDS Weiconlock AN 302-22 SDS      

Related Content & Information.

AN 302-22 Threadlocking Adhesive Demo Video        
AN 302-22 Threadlocking Adhesive Demo Video        

Others Also Bought