Copper Repair Stick - 57gm

SKU: SWM000035B01V0001
MPN: 10530057
Availability: Available for Fast Dispatch.
$13.18
INC. GST
$11.86
EX. GST
Container Size

BULK DISCOUNT RATES

All Bulk Prices Below Are Quoted Including GST.
Buy 6 - 11 and pay only $12.37 each
Buy 12 or above and pay only $12.03 each
  • Extremely fast curing 2-part epoxy adhesive that can be shaped by hand and sets hard. Perfect for repairing copper pipes and parts.
  • Copper filled epoxy putty that is very simple to use with no complex mixing.
  • NSF approved for use in drinking water applications (ideal for sealing and patching pipes).

Weicon Copper Repair Stick is the perfect solution for making fast, lasting and non-rusting repairs to copper pipes, parts and components. This epoxy putty is manufactured in Germany from epoxy resin filled with fillers and has a copper coloured appearance once its cured. Like the rest of our Weicon Repair Stick Range, Copper Repair Sticks are dead simple to use and require no complex mixing. Just cut off the amount you want, knead it in your hands and apply.

Copper Repair Sticks bond well to a variety of materials, surfaces and substrates. These obviously include copper but, in addition, high compatibility is also achieved with a wide range of metals (including aluminium, cast iron, brass and stainless steel) and is also used on hard plastics, fibre reinforced materials, wood, derived timber products, glass, ceramics and stone. It is not suggested for use on rubber materials.

Weicon Copper Repair Stick has been tested and certified in accordance with NSF for use in and around drinking water and food processing systems. It will tolerate some slight wetness or dampness in the application area and is very fast curing (pot life 3 minutes, handling strength after just 10 minutes).

Applications for Copper Repair Sticks

  • Hot and cold water pipe repairs and sealing.
  • Repairs and patching of holes in pipe bends and fittings.
  • Flange repair and sealing.
  • Repairs to worn or rusted copper gutters or sheets.
  • Water heater repair and hole filling.
  • Water tank and hot water system and line repairs.
  • Heating, ventilation and air conditioning system repair and installation.
  • Freeze patching and repairs.

Copper Repair Stick Adhesion Compatibility with Various Material Types

Metal (e.g. stainless steel, brass, cast iron, aluminium) Highly Compatible
Hard Plastics* (e.g. epoxy laminates, rigid PVC) Compatible
Wood (e.g. oak, beech, spruce, balsa) Compatible
Derived Timber Products (e.g. plywood, MDF) Compatible
Fibre Reinforced Materials (e.g. GFRP, CFRP, Fibreglass) Compatible
Glass, Ceramics Compatible
Stone (e.g. granite, brick, concrete, marble) Compatible
Rubber Elastomers Not Compatible

*Performance will vary depending on the exact type of plastic being bonded. Generally, low surface energy plastics will be much harder to bond to then high surface energy (such as rigid PVC).

Colour Copper (Once Cured)
Continuous Operating Temperature -50°C to 120°C
Short-Term Operating Temperature 150°C (2 Hours Maximum)
Maximum Gap Filling 15mm
Basis Epoxy Resin with Copper Fillers
Food Grade No
Potable Water Yes (NSF Approved)
Density 1.9 g/cm³
Pot Life (for 25gm at 20°C) 3 Minutes
Handling Strength (35% of Final) 10 Minutes
Mechanical Strength (50% of Final) 60 Minutes
Final Strength (100%) 24 Hours
Shore Hardness 80 Shore D
Dielectric Strength 3 kV/mm
ISSA Reference Number 75.530.04 (57gm) / 75.530.05 (115gm)
IMPA Reference Number 81 29 75 (57gm) / 81 29 76 (115gm)
SKU SWM000035B01
Brand Weicon

Can it be painted?

Yes, once it is 100% cured. All of our Weicon Repair Sticks can be painted.

What if I don’t use the whole pack?

That’s fine. Just make sure you only mix the amount you need. Pot life doesn’t start until the two components are mixed which is why you need to cut off and knead just the amount you are going to use. It is suggested that any remains have their little foil cover put back over the end, be placed back in their tube, and be kept in the fridge if at all possible as this will extended the useful life of the product.

How hard is it once it’s set?

There’s no easy way to answer this as hard is a little subjective. Let’s just say very, like copper actually. The attached technical data sheet on our Weicon Copper Repair stick gives more specifics of course.

Do I need to do anything special to the surface before sticking the repair stick?

Not really. Just make sure it’s clean and free of dirt, dust or grease (especially true in food areas). If you’re sticking to really smooth surfaces and it’s possible, adhesion will be improved if you roughen the bonding area a little first. Just a bit of sandpaper will often do the job here.

Does it shrink?

Only a very tiny bit. Linear shrinkage is less than 1% during the curing process.

What do I cut bits off with?

Pretty much anything. Really, a butter knife will do the trick here. One thing worth remembering, since pot life is so quick make sure you just cut off and knead the amount you’re going to use immediately. Also, be sure to clean you’re cutting tool as quickly as possible as parts of the putty can stick and cure on it.